Mini draco

Mini draco, Sometimes you just want as much firepower as you can get in the smallest package available. Forget all the talk about 9mm, .45 ACP, .357 Magnum or even 10mm—those are all pistol calibers, and as the axiom goes, “The only good use for a pistol in a firefight is to fight a path to your rifle.”

No, what I’m talking about is rifle calibers. If things go south, most people would prefer a rifle; it’s just not practical to carry one. So, we resort to handguns with all of the limitations of handgun calibers.

But what if your pistol is your rifle? It’d negate the limitations that handguns possess. That’s the intent behind the Mini Draco from Century Arms. It’s an AK pistol chambered in the AK’s legendary cartridge: the 7.62x39mm Soviet.

The Mini Draco is a Romanian-made AK Pistol—made in the Cugir Arms Factory that’s famous for the WASR series rifles—a close copy of the Russian AKM. Per the original Kalashnikov design, it has a stamped sheet metal receiver and incorporates rivets to secure the front and rear trunnions in place. Overall length is 17.5 inches, and it weighs 5.6 pounds without a magazine. Despite the small size of the Mini-Draco, the receiver is the same size as a standard AK.

The rear sight block looks the same as those found on standard-sized AK rifles, but aside from that, everything forward of the receiver is different from the norm. And that’s expected from an AK variant that’s so small. Naturally, the barrel and gas tube are shorter, but to make up for the lack of real estate up front, the front sight and gas block have been combined into one piece. It’s longer (measuring fore to aft), so many AK front sight windage adjustment tools will not work with this.

The muzzle device isn’t the typical slant brake found on an AKM rifle, but it’s instead a compensator (though the Century Arms manual calls it a flash hider) of the same basic design as the government-issue one used on an AR-15, except with different thread (14×1 LH, common to AK rifles) and with three notches at the base.

The receiver internals are standard for an AK of Romanian design, with the exception of the modified rear trunnion and the gas piston (which I’ll get into in a moment). The bolt carrier, bolt assembly and recoil spring assembly are the same as a standard-length AK rifle. To compensate for the short gas tube, the gas piston rod has been removed and only the piston rod head remains. In design, the head has been cut from the piston rod and attached directly to the bolt carrier. In reality, the head isn’t actually cut from the piston rod; it’s a separate machined part.

A hard polymer part called the recoil buffer is positioned in front of the rear trunnion to dampen the impact of the bolt carrier during cycling. Probably the most important function, though, is that it keeps the bolt carrier/gas piston from over-stroking. The recoil buffer looks like it’s from a 3D printer and is a little rough around the edges, so to speak. A piece of hard rubber would’ve probably had better longevity. During disassembly, the recoil buffer will need to be pulled out (it’s not attached) before the bolt carrier can be removed from the receiver.

Century Arms usually uses U.S.-built Tapco triggers in its AK rifles, in part because they’re better than what comes stock, but mostly for 922(r) parts compliance. The trigger in this Mini Draco doesn’t read Tapco, so it looks like a Romanian “government” trigger. It’s pretty good for being a stock trigger, though. It averaged a 5.1-pound pull weight, and it had a crisp break. I’ve pulled many worse Combloc triggers.

There’s no stock since it’s classified as a pistol, so the only furniture is a polymer pistol grip and the front handguard. The handguard is made of blond plywood and has a pretty nice-looking finish, in an industrial kind of way. It doesn’t have a top portion of handgrip, like most AKs, only the bottom.

Build Quality

Century Arms has taken some dings in the past on the roughness of their Romanian AKs, and in general, Romanian AKs have taken some online bashing for being “entry level.” They can be a little rough, but I’ve heard excellent things about reliability, which is the hallmark for AKs.

The Mini Draco that I have has pretty decent build quality. The rivets look good; they’re flush with the receiver surface. I don’t see any creases or bends in the sheet metal. There are no machining marks on the exterior surface of any parts, and even the internal parts/surfaces appear to be pretty good. The magazine well doesn’t have any burrs, nor do any of the other sheet metal edges. The safety selector on mine is very tight and hard to take off safely; it’s the tightest I’ve found on an AK. But hey, any problem that can be solved with a bench vise and a hammer isn’t a problem at all.

There are, however, three things I can see that are negative. The first is the receiver end plate has sharp corners, right where the web of the grip hand rests when shooting. The second is the finish. The finish has a semi-course feel to it that’s typical of what I’ve seen on AKs from the Cugir/ROMARM factory, which is fine with me, but it appears to show wear pretty easy. I haven’t had mine for very long, and there’s quite a bit of wear already. It doesn’t bother me, but it might bother some people, especially those who like to keep their “safe guardians” looking mint.